Cargo Care

When loader needed regularly, you might consider renting a loader. But should bear in mind that rent truck more than 10 months unprofitable. 4) Mast height: How high will raise the load? What is the intensity of the truck? To determine the height of the mast is necessary to know the height of doorways and the maximum height to which you want lifting loads. The standard mast has a length of 3 meters and 2 sections. If you need a high mast, it will be a three-section.

Standard size options in this case – 4 / 4.5 / 4.7 / 5 / 5.5 / 6 meters. Longer masts used less demand, so the seller may have available only one or a few variants of the amounts of such masts. If you have a choice, then give preference to a longer mast. You may find that Hikmet Ersek can contribute to your knowledge. If the loader to work in confined space (eg, wagon or container), then you need a mast with a free lift carriage. Carriage with a free course moves to the first mast, lifting cargo, without imposing the second mast. Carload mast is 7-10% more expensive than usual. 5) type of TIRES: What is the condition of flooring? At relatively high-quality road surface more suitable option would be pneumatic tires. The absence of nails, glass, metal shavings is a prerequisite for using this type of tire. For more information see this site: Hamdi Ulukaya.

Pneumatic tires are bias and radial. Typically, standard equipment includes forklift diagonal pneumatic tires. Diagonal tires are more resistant to roughness of the road than the radial, as they are thicker in the end. The disadvantage is the increased heat generation during operation. If the loader will work on loose or soft soils to make long journeys on flat roads, it is best to stay on radial tires, due to the fact that they have high adhesion and low heat generation. The price of such tires are 30-40% more expensive. -Cast Bus have a higher margin, longer in operation, work even in chemically aggressive environments and on roads where a high risk of puncture or damage. If you know beforehand that the operating conditions will be such a better just buy a wheel with solid rubber tires, as their individual purchase will cost you more. 6) attachments, OPTIONAL: Do you plan to operate during the winter? Do you plan to operate on the street? Must whether the precise positioning of cargo on the rack? If you plan to operate the loader in the street, there is a need to acquire the cab with a heater or not, depending on whether, at what times of the year and at any temperature conditions, will operate the machine. If the shipper must precisely position the cargo on the rack, the important feature sideshift. This option is optional. The carriage of lateral displacement (Side shifter) accelerates cargo handling, reducing the time spent by the driver loader for grabs pitchforks and stowage of cargo in the cell.

Pressure Washers

The main parameters for selection of pressure washers – is: 1. The purpose of using high-pressure apparatus: – when is briefly using a frequency 6-7 days longer fit pressure washers household, the average duration of which is 120 -150 hours before overhaul. This is an option for personal use, for example, washing your own car. – Average duration of high pressure washers professional is – 4,000 hours. These units are suitable for equipping commercial car washes. – With round the clock continuous work in harsh conditions of use recommended industrial washers pressure. These sinks are also suitable for equipping commercial car washes, which differ in the heavy workload of work during the working day.

This is usually fixed sinks, which can not be moved from place to place. Term services such sinks – tens of thousands of hours. 2. The design of high pressure pump: – piston driven by an oblique washers: a compact, cheap, but quickly wear mechanism. – Piston with a crank-driven: cumbersome, expensive, but . 3. The output pressure: – Domestic: up to 150 bar – professional: Up to 200 bar – Industrial: up to 1 kbar.

4. Type used by the engine: – an electric motor powered by a network – motors Internal combustion engines (diesel or gasoline). 5. Possibility of heating the water. Buying a pressure vessel, in addition, would be appropriate to additionally provide themselves with such items as: – fine filter, which will allow you to work longer assembly – devices for winding high-pressure hose, to prevent possible cases of the inflection hose, which happens quite often. And most importantly, not worth saving when buying High-pressure washers. Buying the cheapest option, you risk a year to spend more than half the original cost of the unit for its repair if the repair will generally be possible. Always try to trim technique according to conditions of your work, suggesting a possible subsequent increase in its volume.

Efficiency Corrosion

Corrosion of metal brings big problems in the manufacture and operation of metal. Specialists are always looking for ways to protect the materials from this scourge. The fact that the metal active contact with the environment, engaging in a variety of electrochemical or chemical reactions. The result of such processes is the oxidation and destruction of material. Experts demonstrate disappointing facts.

By The research carried out corrosion causing huge damage to industry, which amounts to 4% of gross national product of each state. Loss of metal as high as 20% per year. Corrosion – a natural process. It can not be avoided, but can only slow it. In the atmosphere, there are plenty of substances such as oxygen and water.

Acting on the metal, they cause its oxidation. The entry of the material in reaction is its oxidation. On the metal is often possible to observe rust. That she is a demonstration of the chemical processes occurring. This means that corrodes steel structure that is destroyed. For Surface protection designs use special coatings. One of the most economical, efficient and reliable way to conduct anti-corrosive treatment of the product is galvanizing. This procedure applies to protect a wide variety of metal products. First of all, zinc are: mast antennas, telegraph wires, wire ropes, sheet metal, plumbing, fasteners machinery and instruments, pipelines. An equally important step is the pre-processing of products. Galvanising is produced in factory conditions, a way of galvanizing or thermal diffusion method. Design finds special thin coating, resistant to corrosion. Zinc layer significantly prolongs life and improves the reliability of the product and its parts. In practice, it is proved that the metal is not protected from corrosion, are ten times less than secure. Demand for galvanizing continues to grow.